| Line 2 was replaced by line 2 |
| - ;DM,DA: Monochromator/Analyser d-spacing [Angstroem]. |
| + ;DM,DA: Monochromator/Analyser d-spacing [[Angstroem]. |
| Removed lines 5-8 |
| - ;AS,BS,CS: unit cell constants [Angstroem] |
| - ;AA,BB,CC: unit cell constants [degrees] |
| - ;AX,AY,AZ: Components of a recip. lattice vector in scattering plane of the sample. A3 is the angle between KI and (AX,AY,AZ). |
| - ;BX,BY,BZ: Components of a second distinct recip. lattice vector in scattering plane. |
| Lines 11-13 were replaced by lines 7-9 |
| - ;ALF1,ALF2,ALF3,ALF4: Horizontal collimation before mono, before sample, before analyser, before detector [minutes FwHm] |
| - ;BET1,BET2,BET3,BET4: Vertical collimation before mono, before sample, before analyser, before detector [minutes FwHm] |
| - ;ETAM,EATS,ETAA: Monochromator/Sample/Analyser mosaic [minutes FwHm] |
| + ;ALF1,ALF2,ALF3,ALF4: Horizontal collimation before mono, before sample, before analyser, before detector [[minutes FwHm] |
| + ;BET1,BET2,BET3,BET4: Vertical collimation before mono, before sample, before analyser, before detector [[minutes FwHm] |
| + ;ETAM,EATS,ETAA: Monochromator/Sample/Analyser mosaic [[minutes FwHm] |
| Lines 17-19 were replaced by lines 13-14 |
| - Lower and upper limits and zeros for all variables given in (iv) |
| - below. L, U and Z are appended as a prefix to the variable names to |
| - indicate Lower limit, Upper limit and Zero. |
| + Lower and upper limits and zeros for all motors. L, U and Z are appended |
| + as a prefix to the variable names to indicate Lower limit, Upper limit and Zero. |
| Lines 28-29 were replaced by lines 23-24 |
| - A5 Analyzer angle (Bragg angle in deg, TOPSI: not used) |
| - A6 Scattering angle at analyzer (twice A5 in deg., TOPSI: not used) |
| + A5 Analyzer angle (Bragg angle in deg.) |
| + A6 Scattering angle at analyzer (twice A5 in deg.) |
| Removed line 31 |
| - SINQ Instruments: |
| Lines 60-62 were replaced by line 54 |
| - QH -\ |
| - QK +-- Components of Q in Reciprocal Lattice Units [R.L.U.] |
| - QL -/ |
| + QH Q in Reciprocal Lattice Units (3 components!) |
| Lines 70-95 were replaced by line 62 |
| - IF1V IF1V and IF2V are currents [Amps] in the vertical-field |
| - IF2V coils for Flipper 1 and Flipper 2. |
| - IF1H Horizontal-field currents are KI*IF1H for Flipper1 and |
| - IF2H KF*IF2H for F2. |
| - HELM Angle between axis of Helmholtz pair one and KI. |
| - F1 -\ Status of flippers one and two; these variables take the |
| - F2 -/ values ON or OFF. |
| - |
| - ''Currents'' |
| - I1 -\ |
| - I2 \ |
| - I3 +-- power supply current values [A] |
| - . / |
| - I11 -/ |
| - |
| - ''Field'' |
| - HX -\ Components of Helmholtz fields at sample in Oersteds. |
| - HY +-- HX is parallel to Q and HY is perpendicular to Q in |
| - HZ -/ the scattering plane. |
| - |
| - |
| - !Increments Variables |
| - |
| - For all motors, virtual motors, currents and field |
| - the identifier for the step used with a SCan command is obtained |
| - by prefixing the variable name with the letter D. |
| + not yet specified |
LIN