| Line 1 was replaced by line 1 |
| - !Electical Connections |
| + !Electrical Connections (these informations are partially obsolete) |
| Lines 3-17 were replaced by lines 3-40 |
| - || ||on cryostat ||on rack (should not be disconnected) |
| - |switch heater, warn light|small 6 pin LEMO below warn light |switch heater on IPS\\fixed connection to warn light power supply |
| - |VTI sensors & heater |10 pin fisher on VTI |sensors A & B + heater (via relay) on LakeShore 340 |
| - |LN2 level |large 4 pin (fisher?) on LN2 neck |sensor 2 on ILM |
| - |LHe level |small 4 pin (fisher?) on LHe3 neck|sensor 1 on ILM |
| - |sample sensors |top of sample stick |sensors C & D on LakeShore 340 |
| - |VTI needle valve motor (not used) |leave unconnected |ITC503 15 pin DSUB |
| - |
| - !Cryogenic connections |
| - |
| - |He recovery |He neck recovery port KF 25 (without valve) |He recovery |
| - |VTI pumping line |VTI pumping port \\ (do not open valve before tube is pumped out) |VTI pump (top port) |
| - |recovery of pumped He (VTI) |VTI pump (side port) |He recovery |
| - |lambda pump (for fields > 10 Tesla)|lambda pump port on He neck |Lambda pump (top port) |
| - |recovery of pumped He (lambda) |lambda pump (side port) |He recovery |
| + || ||on cryostat ||on rack (should not be disconnected) |
| + |switch heater, warn light|(11) small 6 pin LEMO below warn light |switch heater on IPS (45)\\fixed connection to warn light power supply |
| + |VTI sensors & heater |(12) 10 pin fisher on VTI |(4a/4b) ''sensor A/sensor B'' + heater (42) via relay (43) on LakeShore 340 |
| + |Magnet power leads |(22) magnet power connections on LHe neck|(48) magnet power leads on IPS |
| + |LHe level |(13) small 4 pin (fisher?) on LHe neck |(4h) sensor 1 on ILM211 |
| + |LN2 level |(21) large 4 pin (fisher?) on LN2 neck |(4n) sensor 2 on ILM211 |
| + |sample sensors |(14) top of sample stick |(4c/4d) ''sensor C/sensor D'' on LakeShore 340 + heater ''OUT2'' (44) |
| + |VTI needle valve motor (not used) |leave unconnected |ITC503 15 pin DSUB on green platine |
| + |
| + !Cryogenic Connections |
| + |
| + |He recovery |(16) He neck recovery port (without valve) |He recovery |
| + |VTI pumping line |(17) VTI pumping port \\ (do not open valve before tube is pumped out) |(31) VTI pump (top port) |
| + |recovery of pumped He (VTI) |(32) VTI pump (side port) |He recovery |
| + |lambda pump (for fields > 10 Tesla)|(18) lambda pump port on He neck |(31) Lambda pump (top port) |
| + |recovery of pumped He (lambda) |(32) lambda pump (side port) |He recovery |
| + |
| + !Computer Connections |
| + |
| + | |SANS-I\\extra\\terminal server\\psts228|SANS-II |AMOR |
| + |LakeShore 340\\''SERIAL-I/O'' (41) |port 6|port 6 |port 10 |
| + |IPS magnet power supply\\''RS232'' (46) with grey adapter and RJ45|port 8|port 7 | |
| + |ILM211\\''RS232'' (40) with grey adapter and RJ45|port 9| |
| + |
| + [MA11Installation/ma11_fig1.jpg] |
| + [MA11Installation/ma11_fig2.jpg] |
| + [MA11Installation/ma11_fig3.jpg] |
| + [MA11Installation/ma11_fig4.jpg] |
| + |
| + |
| + !Software Configuration |
| + |
| + * the TecsServer and the SeaServer must be running |
| + (if not: in the instruments account, type |
| + ''monit start tecs'' / ''monit start sea'') |
| + * within SEA client select device |
| + ''ma11'' (for the original sample stick) or |
| + ''ma11r'' (for the rotatable sample stick) |
LIN