| Removed lines 5-9 |
| - Please refer to the cryostat and magnet general assembly drawing in conjunction with the diagrams above. |
| - |
| - |
| - ''2.1.1 Magnet Service Necks'' |
| - |
| Lines 12-18 were replaced by lines 7-9 |
| - Coaxial current lead terminal on tall cryostat services neck |
| - (this neck also features the VTI needle valve): |
| - lnner terminal post l+ (start of entire magnet) |
| - (red wire from magnet) |
| - Outer terminal post 1- (end of entire magnet) |
| - (black wire from magnet) |
| - |
| + Coaxial current lead terminal on tall cryostat services neck (this neck also features the VTI needle valve): |
| + * Inner terminal post I+ (start of entire magnet, internal red wire) |
| + * Outer terminal post I- (end of entire magnet, internal black wire) |
| Removed line 20 |
| - ASYMMETRIC ENERGISATION (4 TESLA) Co-axial current lead terminal on short cryostat services neck (this neck also features the syphon entry port):lnner terminal post l+ (start of selected coils) |
| Line 22 was replaced by line 12 |
| - (blue wire from magnet) |
| + ASYMMETRIC ENERGISATION (4 TESLA) |
| Lines 24-25 were replaced by lines 14-16 |
| - Outer terminal post 1+ (end of selected coils) |
| - (brown wire from magnet) |
| + Co-axial current lead terminal on short cryostat services neck (this neck also features the syphon entry port): |
| + * Inner terminal post I+ (start of selected coils, internal blue wire) |
| + * Outer terminal post I+ (end of selected coils, internal brown wire) |
| Line 27 was replaced by lines 18-20 |
| - Ten pin connector on services neck with syphon entry :Connections to persistent mode switch heaters. |
| + Ten pin connector on services neck with syphon entry: |
| + * Connections to persistent mode switch heaters |
| + [MA09WiringManual/SwitchHeaterPlug.gif] |
| Line 29 was replaced by lines 22-24 |
| - Ten pin connector on services neck with lambda point refrigerator needle valve and pumping line:Connections to carbon resistors for monitoring lambda point refrigerator. |
| + Ten pin connector on services neck with lambda point refrigerator needle valve and pumping line: |
| + * Connections to carbon resistors for monitoring lambda point refrigerator. |
| + [MA09WiringManual/AllenBradleyPlug.gif] |
| Line 31 was replaced by lines 26-27 |
| - Ten pin connector on services neck with VTI needle valve :Connections to helium level probe. |
| + Ten pin connector on services neck with VTI needle valve: |
| + * Connections to helium level probe. |
| Line 36 was replaced by lines 32-38 |
| - Ten pin connectors on VTI top plate :VTI heat exchanger thermometry and non-inductive heater. |
| + Ten pin connectors on VTI top plate: |
| + * VTI heat exchanger thermometry and non-inductive heater. |
| + [MA09WiringManual/VTIPlug.gif] |
| + |
| + Ten pin connector on cryostat top plate: |
| + * Heater and carbon resistor for clearing VTI needle valve blockages. |
| + [MA09WiringManual/NeedleValvePlug.gif] |
| Line 38 was replaced by lines 40-41 |
| - Ten pin connector on cryostat top plate :Heater and carbon resistor for clearing VTI needle valve blockages. |
| + Five pin connector on services neck with motor drive: |
| + * Auto-needle valve control for the VTI. (not mounted). |
| Line 40 was replaced by lines 43-44 |
| - Five pin connector on services neck with motor drive :Auto-needle valve control for the VTI. |
| + Original Risų Cabling: |
| + [MA09WiringManual/OriginalRisoeCables.gif] |
| Line 45 was replaced by line 49 |
| - Please see circuit diagram. |
| + [MA09WiringManual/InternalWiring.gif] |
| Removed lines 47-51 |
| - [MA09WiringManual/AllenBradleyPlug.gif] |
| - [MA09WiringManual/SwitchHeaterPlug.gif] |
| - [MA09WiringManual/VTIPlug.gif] |
| - [MA09WiringManual/NeedleValvePlug.gif] |
| - [MA09WiringManual/OriginalRisoeCables.gif] |
LIN