| Line 10 was replaced by lines 10-11 |
| - |AMOR |4 |
| + |AMOR |4 | field perpendicular beam |
| + |AMOR |6.8 | field parallel beam |
| Lines 13-14 were replaced by lines 14-18 |
| - |TASP |3.3 ... 5 |see below |
| - |EIGER |6.8 / 6.2 (full field)| |
| + |SANS-II |6.8 / 6.2 (full field)| |
| + |TASP |6.8 | see below (A3 does not move > 4 Tesla) |
| + |EIGER |6.8 / 6.2 (full field)|goniometer removed |
| + |ZEBRA |6.8 / 6.2 (full field)|L1 = 1500 mm, L2 = 785 mm (1D detector) |
| + |ZEBRA | 5 / 5 |L1 = 1000 mm, L2 = 785 mm (1D detector) |
| At line 17 added 1 line. |
| + Goniometer removed.\\ |
| Lines 38-73 were replaced by line 43 |
| - Provisional force measuremnents on AMOR have shown that |
| - the operation of MA7 on AMOR is allowed with a field perpendicular |
| - to the beam at least __up to 4 Tesla__. |
| - The distance to the shielding wall between AMOR and SANS-II has |
| - to be at least 540 mm, measured from the aluminium window |
| - (or about 870 mm to the magnet centre). |
| - |
| - ''Torque Calculations'' |
| - |
| - In general, the forces are not only radial, but also tangential, |
| - inducing a torque onto the magnet. For estimating the forces |
| - on the fixation, we need to take into account the distance of |
| - the fixation points from the coil center. |
| - |
| - For MA7, with a mean coil radius of about 100 m and fixation points |
| - at about 150 mm for the coil center, we get the following: |
| - |
| - Ro: object distance (mm)\\ |
| - phi: angle (deg) between field direction and direction of object, for maximum force on fixation\\ |
| - Fp: force when object on magnet axis (in field direction) |
| - Ft: maximum total force on fixation |
| - |
| - ||Ro ||phi ||Ft / Fp |
| - |<600 | 0 | 1.0 |
| - | 800 | 20 | 1.04 |
| - | 1000 | 27 | 1.13 |
| - | 1200 | 32 | 1.25 |
| - |
| - For the distance to the shielding wall we have to add 1/5 of the edge |
| - distance for the mean distance of the material that has to be taken |
| - into account (870 * 6/5 = 1044 mm). |
| - |
| - Measured force at 3.4 Tesla: 180 N.\\ |
| - Extrapolated to 5 Tesla: 390 N.\\ |
| - Factor 1.2 for including torque: 470 N.\\ |
| - With a reasonable security margin, we allow to go __up to 4 Tesla__. |
| + Force tests after major instrument upgrade 2023-11-21: |
| At line 74 added 4 lines. |
| + Allowed field when perpendicular to beam: __6.8 Tesla__ (forces 300 N horizontally, 480 N vertically) |
| + |
| + Field parallel to field: __3 Tesla__ (horizontal force 280 N, guide field is moving, not secured enough! this should be fixed) |
| + |
| Lines 77-78 were replaced by lines 51-57 |
| - Distance: sample --> analyzer is set to max value\\ |
| - Be-filter installed ~22 cm from magnet surface (see photo)\\ |
| + Goniometer removed.\\ |
| + Beryllium Filter Distance 27 cm (see photo)\\ |
| + Sample table - Monochromator - 73 cm\\ |
| + ||A2 || a4 || Allowed field |
| + |-92 < A2 < -41 (Ei=14.7 meV)|<= 119 | __6.8 Tesla__ |
| + |
| + __WARNING: Motor A3 may not move with a field > 4 Tesla__ |
| Lines 80-83 were replaced by lines 59-60 |
| - ||A2 || distance sample table --> \\monochromator (see photo)|| Allowed field |
| - |-92 < A2 < -41 (Ei=14.7 meV)|>=57 cm | __5.5 Tesla__ |
| - |-92 < A2 < -56 (Ei=8 meV)|>=57 cm | __5.5 Tesla__ |
| - |-92 < A2 < -80 (Ei=3.5 meV)|>=57 cm | __5.5 Tesla__ |
| + This data is derived from the force test 7. July 2015:\\ |
| + 4.8 Tesla, horizontal force 150 N (towards Beryllium filter), vertical force 180 N. |
| At line 84 added 2 lines. |
| + [MA7Restrictions/taspFilterMA7.png][MA7Restrictions/distanceTASP.jpg] |
| + |
| At line 95 added 4 lines. |
| + |
| + !Force Test on SANS-II 21.5.2015 |
| + |4.9 T perpendicular to beam|300 N vertical|140 N horizontal |
| + |4.9 T parallel to beam|300 N vertical|60 N horizontal |
LIN